The DM‑TX‑201‑C provides an interface for computers and high-definition AV sources as part of a complete Crestron® DigitalMedia™ system. It functions as a DM 8G+® transmitter and switcher with HDMI®, VGA, and analog audio inputs along with Ethernet and USB HID ports for a total connectivity solution.

Its low-profile, surface-mountable design makes the DM‑TX‑201‑C ideal for installation beneath a conference table, inside a lectern or equipment rack, or at virtually any other location in a boardroom, classroom, auditorium, or residence. It connects to the head end or display location using a single CAT type twisted pair cable. In addition to DM 8G+, it is also compatible with HDBaseT® standard, which allows it to be connected directly to the input of an HDBaseT certified display device.¹

Key Features

• DigitalMedia 8G+® transmitter and multimedia interface
• Built-in 2x1 AV switcher with auto-switching and analog audio-breakaway
• QuickSwitch HD™ technology manages HDCP keys for fast, reliable switching
• Connects to a DM® switcher or receiver over a single CAT type twisted pair cable¹
• Supports cable lengths up to 330 ft (100 m) using DM 8G® cable or CAT5e¹
• HDBaseT® Certified standard — Enables direct connection to other HDBaseT certified equipment
• Handles video resolutions up to Full HD 1080p
• Handles computer resolutions up to WUXGA
• Handles Dolby Digital®, DTS®, and uncompressed 7.1 linear PCM audio
• HDCP compliant
• Performs automatic AV signal format management via EDID
• Enables device control via CEC and Ethernet
• Enables USB HID signal extension for a local computer
• Compatible with Crestron® USB over Ethernet Extenders⁶
• Compatible with Crestron Connect It™ Cable Caddies⁷
• Powered via the DM connection or optional power pack (sold separately)^4,5

1. For DM 8G+ or HDBaseT wiring, use Crestron DM-CBL-8G DigitalMedia 8G Cable or third-party CAT5e (or better) UTP or STP. (Crestron legacy DM-CBL DigitalMedia Cable or DM-CBL-D DigitalMedia D Cable may also be used.) The maximum wire length for DM 8G+ is 330 ft (100 m) between devices. Shielded cable and connectors are recommended to safeguard against unpredictable environmental electrical noise which may impact performance at resolutions above 1080p. Refer to the Crestron DigitalMedia Design Guide, Doc. #4546 for complete system design guidelines. DM 8G+ is compatible with HDBaseT Alliance specifications for connecting to HDBaseT compliant equipment. All wire and cables are sold separately.
2. The HDMI connections can accommodate a DVI or Dual-Mode DisplayPort signal using an appropriate adapter or interface cable. CBL-HD-DVI interface cables are available separately.
3. The RGB input can actually accept component, composite, and S-Video signals through an appropriate adapter (not included), or via direct interface to Crestron MPS Series products. However, input sync detection is not provided for composite or S-Video signal types through this connection.
4. To power the DM‑TX‑201‑C using PoDM (Power over DigitalMedia) requires connection to a DM switcher or other DigitalMedia equipment that has a PoDM PSE port. Wiring that connects to a PoDM PSE port is for intrabuilding use only.
5. To power the DM‑TX‑201‑C using HDBaseT PoE requires connection to a switcher or other equipment that has an HDBaseT PoE PSE port. Wiring that connects to a HDBaseT PoE PSE port is for intrabuilding use only
6. USB over Ethernet Extender Modules are sold separately. Refer to the Crestron USB over Ethernet Extenders (USB‑EXT‑DM‑LOCAL and USB‑EXT‑DM‑REMOTE) and Crestron USB over Ethernet Network Wall Plate Endpoints (USB‑NX2‑LOCAL‑1G and USB‑NX2‑REMOTE‑1G) spec sheets for more information.
7. The DM-TX-201-C has a USB device port, which does not supply USB power. When connected to a TT-100 series cable caddy (sold separately), the cable caddy must be powered separately through a connection to a Cresnet® network or power supply. Refer to the TT-100 spec sheet for more information.